Differences

This shows you the differences between two versions of the page.

--- nyan:log [2024/03/05 18:06] – created river
+++ nyan:log [2024/08/28 16:57] (current) – river
@@ Line 1: / Line 1: @@
 ====== Captain's Log ======
+===== Stardate 20240827 =====
+I didn't realise how long it was since I last wrote here. I've been busy working on this and other projects.
+This evening we tested a Nyan box on a boat in Granton harbour. :) Connected to the NMEA2000 bus, it picks up wind instruments, position, and other data, and sends it out over LoRa. We made contact with a meshtastic station over the water in Fife.
+===== Stardate 20240428 =====
+Since last update, I've mostly been working on:
+  * Starting to put together some devices: [[:construction|Electronics Construction / Hardware Notes]]
+  * Repairing and reverse engineering a commercial wind and weather sensor (WXT510), to use with Nyan. (TODO: write up). Seeing how to interface with it: maybe with SDI-12, but it can do some stuff over NMEA0183. Bodging around the corroded electronics. Fibreglassing the case and finding a mounting pole.
+  * Testing a 5V power supply (buck converter) to run Nyan and a pi of 12V nom.
+  * Examined an [[:ngt-1|Actisense NGT-1]]
+  * Testing an [[:as3935|AS3935 Lightning Detector Chip]], with a view to including it on a Nyan board design
+  * Made a webpage at [[https://personal.cis.strath.ac.uk/river.macleod]], for some academic linkjuice?
+  * Talking to people about future marine / environment related research on boats, and how to organise this
+  * Went to see some boats to measure up / see how to fit some nyan devices.
+  * Testing INA3221 current sensors ([[:current_measurement|Current Measurement]])
+  * Build / test a Raspberry Pi Pico W version of nyan prototype. It works, but having trouble with meshtastic python cli.
+  * Tested devboard antennas, and another one I bought, on the LiteVNA. Some are useless, some okish. [[:lora-antennas|LoRa Antennas]]
+  * Tested supplied uFL -> SMA pigtails. They are ok.
+  * Antenna design.
+  * Made a JTAG adapter for debugging the various ESP32 / pi pico boards I am working with.
+  * Admin: repaired lab lighting, and my laptop.
+  * Component shopping.
+  * Receiving, testing, rejecting, and reordering some components.
+  * Learning how to use, and testing, a LiteVNA.
+  * Testing NMEA2000 parts and terminators. The ones I got are not just 120 ohm resistors.
+===== Stardate 20240312 =====
+I am having trouble with WiFi and web interface on two ESP32 devices. The Heltec Wireless stick is not connecting at all, and the Heltec V3 is not accepting a change of SSID, and says it can't see the access point (same error reported by the wireless stick).
+Positive: I have got NMEA2000 / CAN working! A RPi Pico device is receiving and decoding PGNs sent by SignalK.
+===== Stardate 20240309 =====
+Today I have been mostly working on SignalK and NMEA2000. Trying SignalK security tokens (not tested yet because the WiFi on the dev board broke). Testing ([[:can_interfaces|USB CAN adapter]], got [[:signalk|SignalK]] to output data on it, viewed in Wireshark. Also code for handling multiple GNSS sources ([[:gnss|Position Accuracy Assessment]]).
+I have setup a remote dev environment using a single board computer with an ESP32 LoRa dev board connected by USB, and reset pin on a GPIO. Accessed over wireguard, this makes a very convenient way to work without having to move around a bunch of hardware and reconfigure networking when I want to work somewhere else.
+I tried setting up a WiFi AP on the remote machine, but the dev board was not connecting to that either.
+I also setup VNC. Until now I always used X forwarding, but it was super slow. I had assumed that something which knew the protocol and wasn't just shovelling bitmaps would be faster, but apparently not.
 ===== Stardate 20240305 =====
@@ Line 8: / Line 55: @@
 Meshtastic does not support OTA flashing, so at least for prototyping, I shall use Raspberry Pis to talk to them. These can also run SignalK and OpenCPN. Procurement is incredibly slow, but eventually when everything arrives, I shall be building base stations and a boat station for testing. These will consist of a box with a LoRa dev board, a Pi, power supply, NMEA2000 interface, and hopefully decent aerials.
+I'm interested to see how it does at one base station site, where it will be colocated with two other LoRa transmitters on the same band. Meshtastic always reports false preamble detection anyway, so seems like the carrier sense doesn't work. We can also test it with 100W of HF.
 I've just made a script to reset the ESP32 boards with a pi GPIO. Boards with USB->serial chips can do this anyway with correct poking of the UART control lines, but it's nicer to not interfere with a serial terminal, and the ESP32-S3 boards with directly connected USB seem to need a manual reset and press of the flashing mode button.